Sources
Help build the largest human-edited directory on the web.
Submit a site - Become an editor
Wikipedia. Licensed under the GNU Free Documentation License.
Are you an expert in this subject? Join the discussion and share your knowledge at Wikipedia.org.
Mipmap
From Wikipedia, the free encyclopedia
In 3D computer graphics texture filtering, MIP maps (also mipmaps) are pre-calculated, optimized collections of bitmap images that accompany a main texture, intended to increase rendering speed and reduce artifacts. They are widely used in 3D computer games, flight simulators and other 3D imaging systems. The technique is known as mipmapping. The letters "MIP" in the name are an acronym of the Latin phrase multum in parvo, meaning "much in a small space". They need more space in memory although they form the basis of wavelet compression.
Each bitmap image of the mipmap set is a version of the main texture, but at a certain reduced level of detail. Although the main texture would still be used when the view is sufficient to render it in full detail, the renderer will switch to a suitable mipmap image (or in fact, interpolate between the two nearest, if trilinear filtering is activated) when the texture is viewed from a distance or at a small size. Rendering speed increases since the number of texture pixels ("texels") being processed can be much lower than with simple textures. Artifacts are reduced since the mipmap images are effectively already anti-aliased, taking some of the burden off the real-time renderer. Scaling down and up is made more efficient with mipmaps as well.
If the texture has a basic size of 256 by 256 pixels (textures are typically square and must have side lengths equal to a power of 2 (although this restriction does not exist in OpenGL 2.0+)), then the associated mipmap set may contain a series of 8 images, each one-fourth the size of the previous one: 128×128 pixels, 64×64, 32×32, 16×16, 8×8, 4×4, 2×2, 1×1 (a single pixel). If, for example, a scene is rendering this texture in a space of 40×40 pixels, then an interpolation of the 64×64 and the 32×32 mipmaps would be used. The simplest way to generate these textures is by successive averaging, however more sophisticated algorithms (perhaps based on signal processing and Fourier transforms) can also be used.
The increase in storage space required for all of these mipmaps is a third of the original texture, because the sum of the areas 1/4 + 1/16 + 1/64 + 1/256 + · · · converges to 1/3. (This assumes compression is not being used.) This is a major advantage to this selection of resolutions. However, in many instances, the filtering should not be uniform in each direction (it should be anisotropic, as opposed to isotropic), and a compromise resolution is used. If a higher resolution is used, the cache coherence goes down, and the aliasing is increased in one direction, but the image tends to be clearer. If a lower resolution is used, the cache coherence is improved, but the image is overly blurry, to the point where it becomes difficult to identify.
To help with this problem, nonuniform mipmaps (also known as rip-maps) are sometimes used. With a 16×16 base texture map, the rip-map resolutions would be 16×8, 16×4, 16×2, 16×1, 8×16, 8×8, 8×4, 8×2, 8×1, 4×16, 4×8, 4×4, 4×2, 4×1, 2×16, 2×8, 2×4, 2×2, 2×1, 1×16, 1×8, 1×4, 1×2 and 1×1.
The unfortunate problem with this approach is that rip-maps require four times as much memory as the base texture map, and so rip-maps have been very unpopular. Also for 1×4 and more extreme 4 maps each rotated by 45° would be needed and the real memory requirement is growing more than linearly.
To reduce the memory requirement, and simultaneously give more resolutions to work with, summed-area tables were conceived. Given a texture (tjk), we can build a summed area table (sjk) as follows. The summed area table has the same number of entries as there are texels in the texture map. Then, define
Then, the average of the texels in the rectangle (a1,b1] × (a2,b2] is given by
However, this approach tends to exhibit poor cache behavior. Also, a summed area table needs to have wider types to store the partial sums sjk than the word size used to store tjk. For these reasons, there isn't any hardware that implements summed-area tables today.
A compromise has been reached today, called anisotropic mip-mapping. In the case where an anisotropic filter is needed, a higher resolution mipmap is used, and several texels are averaged in one direction to get more filtering in that direction. This has a somewhat detrimental effect on the cache, but greatly improves image quality.
Mipmapping was invented by Lance Williams in 1983 and is described in his paper Pyramidal parametrics. From the abstract: "This paper advances a 'pyramidal parametric' prefiltering and sampling geometry which minimizes aliasing effects and assures continuity within and between target images." The "pyramid" can be imagined as the set of mipmaps stacked on top of each other.